F01 error code Whirlpool dryer : Causes, How FIX Problem (2024)

It sometimes happens that the dryer drum does not rotate and the laundry dries unevenly. And there is an f01 error code on the screen: Whirlpool dryer gives the same combination even in the absence of heating. Or quite often Whirlpool dryer displays f1 error code, without even starting a drying program. What’s the matter?

What is error f1 associated with?

Most often it refers to the electronic control board. It indicates that there is no contact between the central module and the remaining nodes. It is a common problem which is caused by:

  • short-term power failure;
  • an unexpected power surge.

How to correct the situation quickly?

Error code f01 or f1 is sometimes eliminated by rebooting the household appliance. To get the desired result, you need to:

  • disconnect the dryer by unplugging the cord;
  • leave it for 1 – 5 minutes;
  • switch it on again by connecting it to the power supply.

If error f1 disappeared, then it was an ordinary failure. If it appeared again, then the problem is much more serious.

Cardinal actions

The elimination of the problem depends on the type of failure, of which there may be several. The most vulnerable are the subunits associated with temperature control. Some other parts also suffer, instigating several negative consequences with a complex technical solution.

Faulty thermal switch

This element protects against overheating. Therefore, when the device starts to overheat, it opens the circuit, preventing a possible fire. As a result, error code f01 appears on the screen.

Depending on the type and model of equipment, a thermal switch can be located:

  • on a blower body;
  • on a heating element;
  • on a gas burner.

To reach it, it is necessary to unscrew the fasteners and remove the bottom panel from the front of the dryer. At the top of the fan, you will immediately see a thermal switch. To check it, disconnect the two wires and connect the probes of the multimeter.

An industrious part has constant continuity. In case of a lack of continuity, the subunit has burnt out and needs to be replaced. The average price of a thermal switch is $ 20. After reinstalling, connect the device to the network and start operation. Error f1 should disappear.

Faulty thermistor

This is another reason that the Whirlpool dryer displays an f01 error code on the screen and does not start the drying mode. First, you need to make sure the wiring of the thermistor is intact, and then repair the damage by soldering or twisting with insulation. If everything is normal, and error code f01 is persistently displayed on the board, then the element, which reads and controls the temperature inside the dryer, is out of order.

It is located on the fan housing, to the left of the thermal switch. To check it, it’s necessary to disconnect the lower front panel, then to dismantle the filtration channel housing. It will provide free access to the thermistor. It is tested with a multimeter and, if a breakdown is detected, it is changed.

Broken door switch

Error f01 is sometimes associated with the door locking mechanism. When it is tightly closed, the switch is activated, producing a specific click. If this signal is not present, then the subunit is faulty. To check it is enough to start the equipment and listen carefully. Lack of the click is a reason to check the mechanism with a multimeter. If a defect is identified, it must be replaced.

Another solution that will allow you to eliminate error code f1 is gluing the switch with adhesive tape. Layers are glued one on top of another until the door starts to shut properly.

Burnt relay contact on the board

After a power surge or short circuit, one of the contacts on the control module may burn out which entails error code f01. As with most microcircuits, the relay converts 120 VAC, generating pulsed currents through soldered joints.

The presence of this problem can be verified by removing the board and then searching for defective points – burnt, weak, or just worn-out ones. As a rule, they are well defined because they have black soot from sparking.

Error f1 is eliminated by restoring the solder. To do this, use a piece of metal wire or 16 AWG wire. Before soldering, the damaged surface is stripped for maximum adhesion. In the process, you will need simple tools: a screwdriver, a multimeter, pliers and a soldering iron.

Damaged wiring

Whirlpool dryer also displays f1 error code if the wires going to the central module have an opening or unstable contact. To restore the integrity of the harness, it is necessary to:

  • connect unfixed jack plugs to the board;
  • solder or twist damaged ends;
  • replace the entire cable.

Each marked method is used depending on the degree of damage to the wiring. In any case, if the error f01 appeared because of the harness, then it should disappear.

Faulty control board

It is located above the top of the back panel of the dryer. It is not difficult to reach. To do this, you need:

  • unplug the unit and turn to yourself;
  • find the screws at the top of the back wall and unscrew them (a dryer usually has 2 screws, a washing machine has 3 ones);
  • Push the top cover backward and slightly raise it;
  • dismantle the protective panel;
  • remove all plug fittings from the control board, due to which error code f1 appears;
  • unscrew the screws with the hex head ¼;
  • remove the control module together with the support;
  • disconnect the cables and wires, after photographing them;
  • unfasten the mounting of the plate;
  • remove it from the fixing support and replace it.

The price of a new part is (depending on the place of purchase) from $60 to $200. The assembly of the unit is performed in the reverse order. In the end, it is necessary to check if Whirlpool dryer displays f01 error code: switch on the dryer and make a test run.

F01 error code Whirlpool dryer : Causes, How FIX Problem (2024)

FAQs

F01 error code Whirlpool dryer : Causes, How FIX Problem? ›

Touch and hold START to restart the dryer cycle or press POWER to clear the display. For other questions regarding Error Codes, see your Owner's Manual.

How do I fix error code F01 on my Whirlpool dryer? ›

F01 - Error Code - Dryer
  1. Power unit down by turning off the circuit breaker(s) for one (1) minute.
  2. Power unit up by turning on the circuit breaker(s).
  3. Start a time dry cycle.
  4. Monitor the dryer for one (1) minute to ensure the error code does not display again.
Dec 7, 2023

How do I clear the error code on my Whirlpool dryer? ›

Touch and hold START to restart the dryer cycle or press POWER to clear the display. For other questions regarding Error Codes, see your Owner's Manual.

How to reset Whirlpool dryer? ›

To reset a Whirlpool dryer, turn it off & unplug it or flip the breaker > wait 1-2 minutes > restore power & turn it on > run a test cycle.

How do I fix my Whirlpool dryer not starting? ›

Whirlpool dryer not starting? How to fix it
  1. This guide applies to most Whirlpool dryer models, including the following:
  2. Check the power supply.
  3. Check for an issue with the dryer door.
  4. Check for a blown thermal fuse.
  5. Check the start switch.
  6. Check the dryer belt.
  7. Check the dryer motor.
Jun 6, 2022

How do I fix my Whirlpool dryer not drying my clothes? ›

What to check if your dryer isn't drying well
  1. Blocked lint screen. If your laundry is coming out of the dryer damp, it could be that your lint screen needs cleaning. ...
  2. Crushed vent hose. Check the vent hose behind your dryer to make sure it's not crushed or kinked. ...
  3. Improper vent hose installation. ...
  4. Clogged dryer exhaust vent.

How do you clear a Whirlpool error code? ›

Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn't clear, Contact Us or Schedule Service Online.

How do I clean the sensors on my Whirlpool dryer? ›

Remove the lint screen and set aside. Vacuum the interior and exterior of the lint trap with a vacuum crevice tool or brush. Vacuum the moisture sensor strips on the outside of the lint trap. Replace the lint screen.

How to do a hard reset on dryer? ›

Reset your dryer

Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That's it.

How do you check for a blown thermal fuse on a Whirlpool dryer? ›

Pull one wire off the fuse to isolate the circuit. Check it with an ohmmeter for continuity. If the needle doesn't move or digital numbers don't change, then you need a new fuse.

How do I clean my Whirlpool dryer vent? ›

For this step, you'll have to go outside to locate the vent. Remove the vent cover from the exterior of your home. Using your dryer cleaning brush, wipe away dust from the ductwork and use a vacuum with a hose to clear out any remaining debris. Replace the vent cover when complete.

Will unplugging the dryer reset it on Whirlpool? ›

If there is heat to the dryer, simply disregard the error and make a new cycle selection. Resetting the dryer is not necessary. If the dryer does not have heat, replace or reset the fuse or circuit breaker. Disconnect power to the dryer then restore power to perform a full reset.

Why would I need to reset my dryer? ›

Some motors have overload protectors that turn off the motor when excess strain is put on it. Often, dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then press this reset button.

Do a Whirlpool dryer have a reset button? ›

Many Whirlpool dryers have a reset button, but the location and appearance of the button can vary depending on the model of your dryer. In some cases, the reset button may be located on the control panel, while in others it may be located on the back of the dryer.

Why is my dryer turning on but not starting? ›

If your dryer turns on but won't start, the controls may not be operating as expected due to incorrect settings or user error. If your dryer won't start but does turn on, ensure the following: The “Start” button and electric controls are being pressed firmly. The dryer door is firmly closed and latched.

What are the codes on a Whirlpool dryer? ›

What do your tumble dryer error codes mean?
  • F01 — Electronic circuit board fault. ...
  • F02 — Motor circuit fault. ...
  • F05 — Waste pipe blockage or pump issue. ...
  • F06 — Door lock fault. ...
  • F07 — Electronic circuit board fault / heating circuit fault. ...
  • F08 — Heater fault. ...
  • F09 — Software fault. ...
  • F11 — Pump circuit fault.

What causes a Whirlpool dryer not to start? ›

Common reasons a dryer won't turn on

Appliance is set to “Controls Locked” Tripped circuit breaker. Start button wasn't held down long enough. Dryer door not fully latched.

How do I fix the F1 code on my Whirlpool washer? ›

F1 Whirlpool Cabrio error code.

This error code indicates a problem with the main control board or a program fault. To remove the code, you most likely have to replace the main control board.

Top Articles
Latest Posts
Article information

Author: Tyson Zemlak

Last Updated:

Views: 6133

Rating: 4.2 / 5 (43 voted)

Reviews: 82% of readers found this page helpful

Author information

Name: Tyson Zemlak

Birthday: 1992-03-17

Address: Apt. 662 96191 Quigley Dam, Kubview, MA 42013

Phone: +441678032891

Job: Community-Services Orchestrator

Hobby: Coffee roasting, Calligraphy, Metalworking, Fashion, Vehicle restoration, Shopping, Photography

Introduction: My name is Tyson Zemlak, I am a excited, light, sparkling, super, open, fair, magnificent person who loves writing and wants to share my knowledge and understanding with you.